Kaapelitehdas Valid HTML 4.0!
 

Etusivu

Garmin eTrex/eMap/Geko
Garmin GPS 12/38/40
Garmin muut kannettavat
Garmin kiinteät mallit
Magellan
PDA (HP, iPAQ, Palm)

Tilaukset ja tiedustelut
Toimitusehdot
Hinnasto PDF icon
Kuvagalleria

Yleistä kaapeleista
Palautteet
Usein kysytyt kysymykset
Linkit


Printer friendly version


iPAQ 19/22/38/39/54/5500 Series Pinout

Liitintä on kahta eri versiota, tämä on vanhempi malli (käytösä esim. mallissa G-90740):

ja tämä 2005 alusta irtoliittimenä käytössä oleva:

Pin  1
Pin  2
Pin  3
Pin  4
Pin  5
Pin  6
Pin  7
Pin  8
Pin  9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18
Pin 19
Pin 20
Pin 21
Pin 22
V_ADP
V_ADP
V_ADP
V_ADP
Reserved – Do Not Use
DCD RS232
RXD RS232
TXD RS232
DTR RS232
GND
DSR RS232
RTS RS232
CTS RS232
RI RS232
GND
No Connect – Do Not Use
USB Detect
No Connect – Do Not Use
USB – UDC +
No Connect – Do Not Use
USB – UDC -
GND
 
 
 
 
 
       MUSTA
<--- [KELTAINEN]
---> [VIHREÄ]
       VALKOINEN
<--> [VIOLETTI]
       ORANSSI
       SININEN
       RUSKEA
       PUNAINEN
       VIOLETTI
 
 
 
 
 
 
 
 
 
 
 
 
 
GPS T
GPS R
 
GPS -
 
 
 
 
 
 
 
 
 
 
 
 


iPAQ 31/36/3700 Series Pinouts

Pin  1
Pin  2
Pin  3
Pin  4
Pin  5
Pin  6
Pin  7
Pin  8
Pin  9
Pin 10
Pin 11
Pin 12
V_ADP
V_ADP
DTR RS232
GND
CTS RS232
RTS RS232
TXD RS232
RXD RS232
DCD RS232
GND
USB - UDC +
USB - UDC -
 
 
 
<--> [VIOLETTI]
 
 
---> [VIHREÄ]
<--- [KELTAINEN]
 
 
 
 
 
 
 
GPS -
 
 
GPS R
GPS T
 
 
 
 


Palm M125/130/500/505/515/i705 Pinouts


See also http://www.pspilot.de/pppm505/pppm505.html

From left to right
Pin  1
Pin  2
Pin  3
Pin  4
Pin  5
Pin  6
Pin  7
Pin  8
Pin  9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
GND
USB_D+
USB_D-
VBUS
HOTSYNC
NC
GND
ID
Vout
RxD
TxD
DETECT
CTS
RTS
DTR
CHARGE
Signal- and charge ground (connected to pin 7)
Positive USB data signal
Negative USB data signal
USB VBUS signal
HotSync IRQ - +3.3V for button push
Not Connected
Signal- and charge GND (connected to pin 1)
Identification for peripherials
+3.2V supply output, 100mA max.
RS-232 RxD signal (input)
RS-232 TxD signal (output)
peripherial detect - tied to ground by peripherials
RS-232 CTS signal (input)
RS-232 RTS signal (output)
RS-232 DTR signal (output)
+5V charge supply input, 500-700mA
 
 
 
 
 
 
<-> [VIO]
 
 
<-- [KEL]
--> [VIH]
 
 
 
 
 
 
 
 
 
 
 
GPS -
 
 
GPS T
GPS R
 
 
 
 
 


Palm III/V/Handera Pinouts

Pin  1
Pin  2
Pin  3
Pin  4
Pin  5
Pin  6
Pin  7
Pin  8
Pin  9
Pin 10
DTR
+3.3v
RxD
RTS
TxD
CTS
GPI 1 (->3.3v for HotSync)
GPI 2 (20Kohm ->3.3v for
NC (Not Connected)
GND
 
 
<-- [KEL]
 
--> [VIH]
 
 
modem)
 
<-> [VIO]
 
 
GPS T
 
GPS R
 
 
 
 
GPS -

See also http://www.gpsinformation.org/dale/Palm/phardware.htm#cable
http://www.palmos.com/dev/tech/hardware/palmhardware/


RS232 DB9 Connector

(Naaras juotospuolelta)  
 
 
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
 
 
CD/DCD
RD/RX/RXD
TD/TX/TXD
DTR
GND
DSR
RTS
CTS
RI
 
 
Data Carrier Detect
Received Data
Transmitted Data
Data Terminal Ready
Signal Ground
Data Set Ready
Request To Send
Clear To Send
Ring Indicator
Full Handshake Null Modem
DB9
PIN
VÄRI
PIN
DB9
3
TX
VIH
RX
2
2
RX
KEL
TX
3
8
CTS
RUS
RTS
7
7
RTS
SIN
CTS
8
6
DSR
ORA
CD
1
4
DTR
VAL
DTR
4
1
CD
MUS
DSR
6
5
GND
VIO
GND
5
9
RI
PUN
 
 
 


Dell Axim

 
 
 
 
 
 
 
 
 
 
 
 
[Pinout]

[Problem]
Correction to my previous post. After further investigation of the Dell Serial Cable, it is apparent that the Axim does provide power for the serial port. However, the port circuitry (the Sipex IC in the bulge in the cable) is powered down except when there is a valid RS232 signal on Pin 4 (CTS) of the DB9 connector. This would usually be the DTR signal from the attached device--the commport of a PC in the case of synching, or hopefully a similar signal from a GPS receiver. Unfortunately, many of the GPS receivers that use a serial connection do not have an RS232 signal on Pin 4. For those devices that do not provide +3v to +11 volts or -3v to -11 volts on pin 4, they will not turn on the Axim's serial port, and therefore won't communicate with it. In such cases, an appropriate voltage must be 'patched' in so that it can communicate with the Axim.

[Solution]
I would like to pass along some info that I have discovered in trying to make a connection between my Axim and Magellan/Tripmate GPS receivers. What I have found is that the serial port on the AXIM needs to have a valid RS232 signal on Pin 4(CTS) of the Dell Serial Cable. This signal takes the port out of a power down condition. When using the Serial Cable for syncing with a desktop, the DTR signal on the desktop commport does the job.

Neither the Delorme Tripmate nor the Magellan Colortrak supply a signal on that pin, therefore they do not communicate. However, I tried two things that worked. First, I patched a 9 volt battery from Pin 4(CTS) to Pin 5 (ground). This works. Using VisualGPS, I can monitor the satellite signals on the AXIM. Second, I tried connecting Pin 3(RxD of the AXIM serial port--or TxD from the GPS port) to Pin 4 of the AXIM connector. Even though there might be data flowing from the GPS to the AXIM, the chip in the cable of the AXIM doesn't care which logic state the line is in, and therefore takes the serial port circuit out of powerdown. Communications between the GPS and the AXIM work fine with this hookup as well.

Conclusion: a valid RS232 signal is needed on Pin 4 of the Dell Serial Cable to activate the port. (Someone else on this forum identified the chip as a Sipex SP3243ECA. I found a data sheet for the chip, and the above suggestions are consistent with the operation of the chip.)


HP Jornada 540/560 12-pin

 
 
 
 
 
 
 
 
 
 
 
 


Miscellaneous cables and documents

 
 
 
 
 
 
 
 
 
 
 
 
PDF icon  USB A/M to pigtail
PDF icon  DB9 with 2.1x5.5mm DC jack to pigtail
PDF icon  iPAQ 22 pin to pigtail
PDF icon  iPAQ 12 pin to pigtail
PDF icon  NSPI 3.15V schematics
PDF icon  Designing TL494 regulators
PDF icon  Garmin 7 pin connector
PDF icon  TC55 LDO regulators